Innotech Genesis II Digital Controller (v5) Manuel d'utilisateur Page 9
- Page / 124
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Page 9 © Mass Electronics Pty Ltd 2010Edition 2.0 dated 06/12/2013
SENRx Wireless Temperature Sensor (Back View) ................................................. 73
Checking Power Input .............................................................................................79
Checking Digital Input Wiring .................................................................................81
Checking Dry Contact Inputs .................................................................................. 83
Checking Digital Output Wiring ..............................................................................85
Analogue Input Signal Conditioner (AISC) Locations ............................................ 87
Address Jumpers, Typical Settings ........................................................................92
End of Jumper, Typical Location ............................................................................93
Setting Analogue Output Jumpers.........................................................................94
Setting Frequency Jumpers on the GENII WMI ......................................................95
Setting Frequency Jumpers on the SENRx Module ...............................................95
Correct and Incorrect Bus Topology.....................................................................105
Adding Modules to a Network ..............................................................................106
Linking Networks in Dierent Locations ..............................................................107
Multi-Network Arrangement .................................................................................108
Example of a Simple REM Network ......................................................................108
Example of REM Network with an Innotech Repeater IR11 ................................109
REM Network with Digital Controller in the middle of a run ............................... 109
REM Network with Innotech Repeater IR11 in the middle of a run ....................110
Use of Repeaters to expand the Primary Network ..............................................111
Example of Comms Screen Connection ...............................................................112
Typical Comms Network Connections ................................................................. 112
Innotech Repeater IR11 and IR12 ......................................................................... 114
Networking and Earthing the Innotech Repeater IR12 .......................................115
GENII MPI Modem and Printer Interface ..............................................................116
Hazardous Connection Example, Circuit 1 ..........................................................117
Hazardous Connection Example, Circuit 2 ..........................................................118
Use of GENII MPI, Circuit 1 ....................................................................................119
Use of GenII MPI, Circuit 2 ..................................................................................... 120
Voltage Check, Isolated/Non-Isolated Digital Controller .................................... 122
Voltage Check, GENII MPI with Isolated/Non-Isolated RS485 .............................122
Voltage Check, Innotech Repeater .......................................................................123
Figure 3-23:
Figure 4-1:
Figure 4-2:
Figure 4-3:
Figure 4-4:
Figure 4-5:
Figure 4-6:
Figure 4-7:
Figure 4-8:
Figure 4-9:
Figure 4-10:
Figure 5-1:
Figure 5-2:
Figure 5-3:
Figure 5-4:
Figure 5-5:
Figure 5-6:
Figure 5-7:
Figure 5-8:
Figure 5-9:
Figure 5-10:
Figure 5-11:
Figure 5-12:
Figure 5-13:
Figure 5-14:
Figure 5-15:
Figure 5-16:
Figure 5-17:
Figure 5-18:
Figure 5-19:
Figure 5-20:
Figure 5-21:
List of Illustrations (Continued)
- INSTALLATION INSTRUCTIONS 1
- Proprietary 2
- Trademark 2
- Disclaimer 2
- Document Management 3
- Document Title: 3
- Revision History 3
- Contents 5
- Contents (Continued) 6
- List of Illustrations 8
- List of Tables 10
- Chapter 1 - Preliminary 11
- Information 11
- 1-1 Introduction 12
- Table 1-1: Document Chapters 13
- 1-2 Special Considerations 14
- 1-3 Unpacking Instructions 14
- 1-4 Installation Plans 14
- 1-5 Tools and Test Equipment 14
- Chapter 2 - Mechanical 15
- 2-1 Introduction 16
- 2-2 Physical Descriptions 16
- Mounting Hole 17
- Typical of 8 17
- GENESIS MPC 19
- GENESI S 20
- ANALOG INPUT 20
- DO 1 DO 2 DO 3 23
- MOUNTING 25
- 2-3.1 DIN Rails 26
- Side View 28
- Top View 28
- 90 Degrees 28
- 2-4 Dierence Data 29
- Chapter 3 - Electrical 31
- 3-1 Introduction 32
- 3-4.1 REM Power Connections 50
- 3-4.2 REM Comms Connections 51
- DIGI TA L OUTPUT 56
- Remote Expansion Modul e 56
- ISOLA TED DIGI TA LINPUT 57
- PULSE INPUT 58
- 24V AC or DC Supply 64
- 0V AC or DC Supply 64
- C ON TROL S YSTEMS 66
- USTRALIA 66
- Chapter 4 75
- Commissioning 75
- 4-1 Introduction 76
- JUMPER WIRE 81
- SWITCH CLOSED 83
- SWITCH OPEN 83
- GENII DI REM 83
- EXTERNAL 85
- GENESIS II DDCINNOTECH 87
- 4-1.3 Install AISCs 90
- 4-1.4 Set Jumper Plugs 91
- AI 5 A I6 AI7 AI8 AI 9 92
- RS485 COMMS 93
- CONNECTIONS 93
- END-OF-CABLE 93
- GEINNOTECH 94
- 4-1.6 Initial Tests 97
- 4-1.7 Final System Check 99
- Chapter 5 - Network 101
- Installation 101
- 5-1 Overview 102
- 5-2 Genesis II Products 102
- 5-2.1 Definitions 103
- 5-3 Installation 104
- 5-3.3 Wiring Topology 105
- Zone A Zone B 107
- Zone BZone A 107
- Repeater 108
- Page 109 109
- - - - - 111
- Page 113 113
- Building A 115
- Building B 115
- DANGEROUS EARTH CONNECTION! 117
- NOT TO BE USED! 117
- Page 119 119
- Page 121 121
- MPI With Isolated RS485 122
- Isolated from 123
- Connected to 123
- Innotech Support 124
© 2020, manymanuals.fr. Tous droits réservés | 0.174 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels